Home

Hull / Deck

• White GRP Hull (massive laminate), Bulkheads laminated to the hull, isophtal-acid-gelcoat plus isophtal-acid-resin in combination with some hand laid layers of powder bound glass fibre matt in the outer layers avoids the diffusion of water and obviates damage by osmosis. Hand laid layers of glass fibre and woven rovings for the inner layers, reinforced bottom section, (Inboard-) Casing for Centreboard, floor (bilge ribs) and keelson.

• Deck and cabin top (white gel coat) massive GRP (hand laid) , Cabin top and foredeck with a water repellent, closed porous foam core for more stiffness in this area, Teak side deck, Teak toe rail and protecting rib

Rigg

• Mast, butted to the top, 2 pairs of Spreaders and Boom made of anodized Aluminium, adjustable preventer backstay, inside running halyards, 2 reef ropes, set up for spinnaker, all halyards and trimming ropes redirected to the Cockpit, Shrouds and Stays made of stainless Steel

Decks Layout

• Self draining chain locker, self draining cockpit with lockable cockpit lockers, 2 Plexiglas cabin windows, 1 port light, 4 mooring cleats, 2 Genoa winches, 2 halyard winches, 2 winch handles, 6 halyard locks, 2 distributor blocks (6-sheaves), 4 Genoa tracks with slides and “PinStop”, Main sheet traveler with trimming ropes, sliding hatch with garage, two-parted door board for companionway, Teak on cockpit seats, Teak on cockpit floor

Extensions

• Stainless Steel Centreboard (12mm thick)
• Special rudder with lift- und swing device, tiller and tiller extension

Interior / Equipment

• Interior as shown on drawings, Woodwork in Sapele, upholstery for salon benches and berths 10 cm thick (div. colours available), Galley, Fore cabin separated with a door, double berth and lockers in the fore cabin (as an opt.) resp. big stowing room for sails or the like, Salon benches to both sides of the centreboard casing, one in a L-style could use as a double berth (as an opt.), sideboards with stowing space and lockers, fold out tableboards on both sides of centreboard casing, quarter berth on starboard side
• Yacht-toilet in fore cabin (as an opt. - or as a separated Room in the main cabin on STB-Side instead of the quarter berth -> see price list for opt. equipment)

Electrical Equuipment Service-Battery 12 V 65 Ah (AGM-Technology), 12V switch and fuse panel, navigation lights, 2 cabin lights

Without Sails

Individual changes are possible for an additional amount. Ask for a special offer!

• • 10 hp Nanni Inboard engine, 20 ltr. Diesel tank, 2-blade folding propeller, lead acid battery
  • Outboard engine, 8-10 hp - depending on Type and Producer
  • Outboard bracket (lift up), mounted, with lanyard
  • toilet “Porta-Potti” in the fore cabin on STB side
    • Pump toilet with holding tank, disposal via seacock and deck suction in the fore cabin instead of the “Porta-Potti”
    • Separated room for the toilet in the main cabin on STB-Side instead of the quarter berth. Pump toilet with holding tank (approx. 50 ltr.) via seacock and deck suction
    • Porthole to open in toilet room
    • additional locker in the fore cabin (STB side), same style as on port side
  • Freshwater option incl. washbasin in Galley and toilet room and water tank (approx. 50 ltr.)
  • 2-flame spirit stove for Galley
  • 2-flame gas cooker incl. gas cylinder and stowing box for gas cylinder
  • upholstery for the fore cabin (for a comfortable double berth instead of stowing room)
  • 2 additional sideboards with stowing space in the fore cabin
  • L-style berth in main cabin prepared for the use as a double berth (“lay in back rest”)
  • chart table on the front end of the quarter berths (not with the sep. toilet room)
  • additional port light in Cabin roof (Lewmar LP 30) incl. mounting
  • Pulpit with bow fitting and anchor lead sheave
  • Boarding ladder (with transom reinforcement etc.)
  • Genoa track, 3 mtr. long with 4 slides (instead of two short tracks on each side)
  • Genoa slides with trimming lines, redirected to the cockpit
  • Upgrade Decks layout, Quick reef (2 ropes each), 7-sheaves distributor blocks, 2 servo cleats
  • Spinnaker halyard, spinnaker boom, topping lift and downhaul
  • Running Backstays (Dynema 6 mm) incl. lanyard (twofold - Herkules 6mm) with add. equipment *
  • Cove locker in Cockpit coaming (on STB and Port side)
  • build in socket for flagpole (stainless steel), flagpole (wood, 750 mm)
  • Self tacking jib System (track, sheet slide, sheet redirection, etc.)
  • Mainsail made by „Moritz“
  • Genoa 3 made by „Moritz“
  • Genoa 1 made by „Moritz“
  • Self tacking jib made by „Moritz“ (ca. 11,9 qm)

  * to equip the mast with an additional spinnaker halyard at the top of the mast ( top spi) backstay are mandatory